40 Programming SATEL

Max. no violation time – exceeding the maximum time of no violation is recognized by the

control panel as a detector failure. The time will only be counted when the zone is

disarmed. If the value 0 is programmed, control of this time is disabled. The time can be

programmed in hours or minutes.

It is recommended that you program the M

NO VIOLATION TIME

parameter, since it will

provide an additional supervision of the detector connected to the zone.

3.3.5 Zone types

0. E

NTRY

XIT

– a delayed zone combining two functions:

entry – violation of the zone starts entry delay counting in the partition and turns on delay

for the 3.

NTERIOR DELAYED

type zones;

exit – violation of the zone during exit delay countdown is equivalent to the partition exit.

1. E

NTRY

– violation of the zone starts entry delay counting in the partition and turns on delay

for the 3.

NTERIOR DELAYED

type zones.

2. D

ELAYED

– a delayed-action zone with optional signaling of delay countdown in keypads.

3. I

NTERIOR DELAYED

– the zone operates as a delayed one when:

– violation of another zone has triggered the entry delay countdown in the partition;

– the delay will be activated using the INT-ENT entry keypad (see the INT-SCR

multifunction keypad manual);

– arm mode type 2 or 3 is active and the D

ELAY IN

2&3

TYPE ARMING

option is enabled for

the zone.

In other situations, the zone will act as an instant one.

4. P

ERIMETER

– instant zone, which is already armed during exit delay countdown.

5. I

NSTANT

– instant zone.

6. E

XIT

– violation of the zone during exit delay countdown is equivalent to the partition exit.

7. D

IGHT

– if disarmed, the zone will signal violation acoustically in keypads and on

the 9. DAY

LARM

, 12. S

ILENT ALARM

and 116. I

NTERNAL

IREN

outputs. When armed, the

zone acts as the 5. I

NSTANT

zone.

8. E

XTERIOR

– a zone with alarm verification: zone violation will start counting the surveillance

time – if a second violation takes place during this time, an alarm will be triggered. If the

URVEILLANCE TIME

is not programmed (the value 0 is entered), the alarm will be generated

upon the first violation.

9. 24

AMPER

– permanently armed zone, intended for the tamper circuits. The zone

violation will additionally cause a trouble condition.

10. 24

IBRATION

– permanently armed zone, intended for working with vibration detectors.

If the partition includes the 10. 24

IBRATION

zone, starting the procedure of arming

from the LCD keypad will initiate a test of vibration detectors (the 39. T

EST VIBRATION

DETECTORS

output is activated and the countdown of time remained to the test end is

running).

11. 24

ASH MACHINE

– permanently armed zone, intended for protection of a cash machine.

12. PANIC-

AUDIBLE

– permanently armed zone, intended for operating the panic buttons.

13. PANIC-

SILENT

– permanently armed zone, intended for operating the panic buttons.

Violating the zone will trigger a silent alarm.

14. M

EDICAL

–

UTTON

15. P

ERSONAL EMERGENCY

The zone types 14 and 15 trigger alarm signaled in the LCD keypads and on the 12. S

ILENT

ALARM

outputs. The names of zones and codes of events from these zones are consistent

with the Contact ID reporting format.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 81 82

Komentáře k této Příručce

Žádné komentáře

ClearOne Interact Serial Command Guide manuales

Manuales del propietario y guías del usuario para Accesorios de audio ClearOne Interact Serial Command Guide.
Ofrecemos 1 manuales en pdf ClearOne Interact Serial Command Guide para descargar gratis por tipos de documentos: Manual de usuario

Clearone Interact Serial Command Guide Manual de usuario (61 paginas)

Marca: Clearone | Categoria: Audio accessories | Tamaño: 0.52 MB |

Tabla de contenidos

TYPE AND DEVICE IDS

CONVENTIONS

COMMAND SUPPORT TABLE

AAMB – Adaptive Ambient Mode

Page 8 of 56

(Null to query in text)

TEXT FORM DETAILS

Page 10 of 56

AGC – Automatic Gain Control

AMBLVL – Ambient Level Adjust

BAUD – Baud Rate

CALLDUR – Call Duration

CAMMOVE – Move the Camera

CAMPOSITION – Camera Position

CAMPRESET – Camera Preset

CAMTRACK – Camera Track

CAMZOOM – Camera Zoom

CLOCK – Clock Set

COMPRESS – Compressor

COMPSEL – Compressor Select

COMVER – COM Version

COUNTRY – Country Selection

DECAY – Decay Rate

DEFAULT – Default the Unit

DIAL – DTMF Dialing

DID – Device ID

Page 20 of 56

DSPVER – DSPVersion

DSPVEREX – 8i DSP Version

DTMFLVL – DTMFTone Level

ARGUMENT FORM:<Value>

EQ – Equalization

EQSEL – Equalization Enable

ERROR – Error Notification

FILSEL – Filter Selection

FILTER – Filter Parameters

FLOW – Flow Control

FMP – First Mic Priority

FPGAVER – FPGA Version

FPGAVEREX – FPGA Version

FREQTABLE – Frequency Table

GAIN – Gain Adjustment

GATE – Gate Status

GHOLD – Gate Hold Time

GMODE – Gating Mode

GMUTE – Global Mute

GRATIO – Gate Ratio

GREPORT – Gate Report

HCONF – Headset Configuration

HOOK – Hook Flash

HOOKD – Hook Flash Duration

LABEL – Label

LOCALNUM – Local Number

LOGMASK – Event log mask

LVL – Level

LVLREPORT – Level Report

MLINE – Mic/Line

MTRX – Matrix Routing

MTRXCLEAR – Matrix Clear

MTRXLVL – Matrix Level

MUTE – Mute

NLP – Non-Linear Processing

OFFA – Off Attenuation

PAA – PA Adaptive

PODVER – POD Version

PP – Phantom Power

RADIOEN – Radio Enable

RADIOSCAN – Radio Scan

RADIOSTATS – Radio Statistics

RAMP – Ramp Gain Adjustment

REFSET – Reference Set

RESET – Reset

RESETUSB – Reset USB

RFVER – RF Version

RING – Ring Indication

RINGEREN – Ringer Enable

RINGERIGN – Ringer Ignore

RXBOOST – Receive Boost

SPEEDDIAL – Speed Dialing

SPLEVEL – Speech Lift Level

SPLIFT – Speech Lift Mode

SYSCHECKS – System Checks

TE – Telco Enable

UID – Unit ID

VER – Version

VEREX – Firmware Version

VOLBUT – Volume Button

VOLUME – Volume Adjustment

ZDIAL – DTMF Dialing USB

ZRING – Ring Indication USB

ZTE – Telco Enable USB

Error Messages

DESIGNATIONS

Más productos y manuales para Accesorios de audio ClearOne

Modelos	Tipo de documento
AP IR Remote	Manual de usuario ClearOne AP IR Remote User Manual, 9 paginas
GT1524	Manual de usuario ClearOne GT1524 User Manual, 42 paginas
Converge 590	Manual de usuario ClearOne Converge 590 User Manual, 136 paginas
RAV 900	Manual de usuario ClearOne RAV 900 User Manual, 63 paginas
XAP IR Remote	Manual de usuario ClearOne XAP IR Remote User Manual, 11 paginas
XAP Net	Manual de usuario ClearOne XAP Net User Manual, 16 paginas
XAP TH1	Manual de usuario ClearOne XAP TH1 User Manual, 36 paginas
XAP TH2	Manual de usuario ClearOne XAP TH2 User Manual, 60 paginas
AccuMic PC	Manual de usuario ClearOne AccuMic PC User Manual, 2 paginas
XAP400	Manual de usuario ClearOne XAP400 User Manual, 173 paginas
RAV Wired Control	Manual de usuario ClearOne RAV Wired Control User Manual, 2 paginas
RAV 900 EMEA QSG	Manual de usuario ClearOne RAV 900 EMEA QSG User Manual, 12 paginas
Table Controller for XAP	Manual de usuario ClearOne Table Controller for XAP User Manual, 17 paginas
BluePort NS-BP200	Manual de usuario ClearOne BluePort NS-BP200 User Manual, 12 paginas
StreamNet Infrastructure and Network	Manual de usuario ClearOne StreamNet Infrastructure and Network User Manual, 22 paginas
StreamNet Integration	Manual de usuario ClearOne StreamNet Integration User Manual, 55 paginas
ViewLinX - VL9300	Manual de usuario ClearOne ViewLinX - VL9300 User Manual, 14 paginas
StreamNet StarDraw Control	Manual de usuario ClearOne StreamNet StarDraw Control User Manual, 13 paginas
StreamNet Internet Radio	Manual de usuario ClearOne StreamNet Internet Radio User Manual, 18 paginas
IP Speaker	Manual de usuario ClearOne IP Speaker User Manual, 7 paginas

Satel INTEGRA Plus Specifikace Strana 42

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Satel INTEGRA Plus

ClearOne Interact Serial Command Guide manuales

Clearone Interact Serial Command Guide Manual de usuario (61 paginas)

Tabla de contenidos

Más productos y manuales para Accesorios de audio ClearOne