Satel INTEGRA Plus Specifikace Strana 31
- Strana / 82
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SATEL INTEGRA Plus 29
the "Configuration" window, "Modem" tab). A suitable message will inform about the
connection being established.
Connection initiated by the control panel – external modem
1. Click on the button in the D
LOAD
X program.
2. A drop-down menu will be displayed. Select the "Modem - INTEGRA with ext. modem" in
it. A window will open in which modem initialization information will be displayed.
3. In the LCD keypad connected to the control panel, start the S
TART
DWNL-MOD function
([code] D
OWNLOADING
S
TART
DWNL-MOD). The function is available to the installer,
administrator and user having the D
OWNLOADING STARTING
right.
4. The control panel will call the programmed computer telephone number.
5. The D
LOAD
X program will answer the connection automatically or the program user must
accept establishing the communication (which depends on the settings programmed in
the "Configuration" window, "Modem" tab). A suitable message will inform about the
connection being established.
2.2.7 Starting remote programming via Ethernet network
Programming through the Ethernet network is possible, if the ETHM-1 module is connected
to the control panel (the RS-232 ports of control panel and module must be connected).
The connection can be established in two ways:
1. Initiating connection from the D
LOAD
X program. This method enables establishing a
connection with the control panel from any location.
2. Initiating connection by the control panel. The control panel can only be remotely
programmed from a specific location. This method is applicable when the system user
does not want the remote programming to take place without the user's knowledge.
Configuring the alarm control panel and ETHM-1 module
In the control panel you must:
disable the local programming function (see section F
INISHING LOCAL PROGRAMMING
p. 26);
enable the E
XTERNAL MODEM
option;
enable the M
ODEM
ISDN/GSM/ETHM
option;
enable the A
NSWERING
-
ETHM/GSM
option.
In the ETHM-1 module you must:
program the number of TCP port which will be used for communication;
program the key with which the data sent through the Ethernet will be encrypted;
enable the D
LOAD
X
->
ETHM-1
CONNECTION
option if the connection is to be initiated by the
D
LOAD
X program;
program the network address of the computer with D
LOAD
X program (or the server whose
port has been redirected to the computer), if the connection is to be initiated by the control
panel.
The above-mentioned options and parameters can be programmed:
using the keypad, in the service mode (O
PTIONS
submenu and ETHM-1 module settings
[H
ARDWARE
E
XPANDERS
S
ETTINGS
]);
using the D
LOAD
X program during local programming ("Options" window and ETHM-1
module settings in the "Structure" window, "Hardware" tab).
- PROGRAMMING 1
- 2 Programming SATEL 4
- SATEL INTEGRA Plus 3 5
- 1. General 6
- 2. Programming options 6
- 2.1.5 Service mode menu 7
- 6 Programming SATEL 8
- SATEL INTEGRA Plus 7 9
- 8 Programming SATEL 10
- SATEL INTEGRA Plus 9 11
- [n – counter number] 11
- SATEL INTEGRA Plus 11 13
- [n – identifier number] 13
- 12 Programming SATEL 14
- SATEL INTEGRA Plus 13 15
- 14 Programming SATEL 16
- SATEL INTEGRA Plus 15 17
- 16 Programming SATEL 18
- SATEL INTEGRA Plus 17 19
- (only INT-S and INT-SK) 19
- (only INT-SCR) 19
- [n – number of output] 19
- 18 Programming SATEL 20
- SATEL INTEGRA Plus 19 21
- (does not apply to CA-64 DR) 21
- 20 Programming SATEL 22
- SATEL INTEGRA Plus 21 23
- 22 Programming SATEL 24
- 2.2 DLOADX program 25
- 24 Programming SATEL 26
- SATEL INTEGRA Plus 25 27
- 26 Programming SATEL 28
- program 29
- 28 Programming SATEL 30
- SATEL INTEGRA Plus 29 31
- LOADX program 32
- Configuring the GSM module 33
- Initiating a connection 33
- 3. System structure 34
- 3.2.3 Partition parameters 35
- Partition type 36
- Options 37
- 3.3 Zones 38
- 3.3.3 Programming the zones 39
- 3.3.4 Zone parameters 39
- 38 Programming SATEL 40
- SATEL INTEGRA Plus 39 41
- 3.3.5 Zone types 42
- SATEL INTEGRA Plus 41 43
- 3.3.6 Zone options 44
- SATEL INTEGRA Plus 43 45
- 44 Programming SATEL 46
- 3.3.7 Counters 47
- 3.3.8 Bypasses 47
- 4. Outputs 48
- 4.1 Output parameters 49
- 4.2 Output functions 49
- 48 Programming SATEL 50
- SATEL INTEGRA Plus 49 51
- 50 Programming SATEL 52
- SATEL INTEGRA Plus 51 53
- 4.3 Options 54
- 4.4 Output triggering 54
- 4.6 Output disabling 55
- 4.8 Output groups 56
- 4.9 Output state indicating 57
- 4.11 Output testing 57
- 5. System options 58
- 5.2 Printer options 59
- 5.3 Other options 60
- SATEL INTEGRA Plus 59 61
- 4 Arming options 62
- Times 5.5 63
- 5. r parameters 63
- 62 Programming SATEL 64
- 6. Programming the keypads 65
- 64 Programming SATEL 66
- SATEL INTEGRA Plus 65 67
- 66 Programming SATEL 68
- 7. Timers 69
- 8. User schedules 70
- 9. Reporting 70
- SATEL INTEGRA Plus 69 71
- 9.1.2 Advanced options 72
- Identifiers 73
- SIA / TELIM prefix 74
- Events assignment 74
- 9.1.4 SIA-IP 74
- 9.1.6 Event codes 74
- 9.2 Starting the reporting 75
- 9.2.3 GPRS reporting 76
- 10. Messaging 77
- 76 Programming SATEL 78
- 10.2.1 Events assignment 79
- 78 Programming SATEL 80
- SATEL INTEGRA Plus 79 81
- 13. Manual update history 82
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Satel INTEGRA Plus
(27 stránky)Compaq Kit per auto manuali utente
Partendo da I
Komentáře k této Příručce